Stuff breaks or requires maintenance, and fishing tackle is no exception. A few days after Christmas, I’ll take time to check tackle and get it ready for next season. Better to find a problem now than with a trophy striper or lunker bass tearing out line.
Recommended Stories
Checks for fishing tackle are simple. For rods, take them into the shower, and scrub around the guides and reel seats with an old toothbrush. That gets rid of dried algae around the guides and gunk on the reel seat.
Remove old wax and possible dirt build-up on male ferrules. When dry, recoat rod ferrules with candle wax for a tight section fit.
Get rid of old line, and add new premium line. Remove line and discard it in a plastic bag and out with the trash to keep small critters from tangling in it.
Use care to dismantle tackle. Reels can be complicated. Do any repairs or dismantling only if you are mechanically inclined and have the reel manual complete with schematics. And only dismantle the reel as far as necessary. If you are not sure what to do, take it to your tackle shop.
For easy reassembly, remove each part in turn and place it in order in an egg carton or biscuit tin. That way reversing the removal process makes it easy to reassemble parts in order.
With the spool bare of line, clean it with a rag or old toothbrush, then polish it. Before taking the reel apart, use the toothbrush and rag to thoroughly clean the reel’s exterior.
With spinning reels, remove the handle, followed by the side plate. Often that’s as far as you have to go. Removing the side plate allows checking the gears for enough grease, checking for water intrusion, and greasing the gears and reciprocating spool shaft. If there is water present, dump it out, allow the reel to dry for a few days, then remove the old grease and relubricate the reel.
To lubricate, use a toothpick to deposit a tiny drop of grease on each gear tooth. Just dropping a lump of grease into the gear housing won’t work. With the side plate off, check the anti-reverse to make sure it works smoothly. Replace the side plate and screws in order.
Check the movement of the bail to flip open and closed. Be careful when removing a cover plate over a bail spring mechanism. If needed, clean these parts and then reassemble, working on one side of the bail at a time.
Remove and check the roller. Roller binding or stoppage wears out line rapidly. Clean and re-lubricate using a light oil as recommended by the manufacturer.
For casting reels, you can also remove the reel handle, then each side plate in turn. Usually the left side plate holds the magnetic cast control or the centrifugal cast-control brake blocks. These brake blocks slide freely on rods — don’t lose them. The right side plate usually holds the gearing and star drag. Back off the drag, check it for lubricant, then grease the main and pinion gears.
Remove the cap holding the level wind pawl. Replace the pawl if worn, otherwise oil the pawl and the level wind worm gear.
Fly reels are the easiest of all, and in most cases they do not need any invasive operations, provided that you back off the drag and wash and clean the reel to prevent corrosion. It’s not necessary to remove the line or Dacron backing.
To add new line to spinning, casting and revolving spool reels, tie the line to the spool arbor, make a few turns and then tape the line in place. Additional wraps create pressure on the taped spool knot to prevent the line from slipping. This is important to prevent line slippage on the polished spool or line binding in coils if the line is laid on too loosely.
Unless the reel drag is sticky or erratic, leave it alone. Be sure to back it off completely during storage and also after each fishing trip.
All this takes only a few hours. And to avoid major problems this time next year, rinse off the rod and reel after each saltwater trip and back off the drag so it works when you need it.
C. Boyd Pfeiffer is an internationally known sportsman and award-winning writer on fishing, hunting, and the outdoors. He can be reached at cbpfeiffer@msn.com.